Minnesota Waterproofing

It's getting close to springtime in Minnesota and with the heavier than usual snowfall that means lot's of moisture.  This year will probably be different than last year where the ground was frozen solid and a lot of moisture was entering foundations through cracks that extended above grade level. 

This block wall foundation is a great example of several mistakes done by the owner hoping to keep water from entering his foundation and one that was a headache for the homeowner last year during the spring thaw. 

The first mistake is having the downspout end just a few inches from the ground where it is more susceptible to freezing and clogging up.  We always recommend about 18" off the ground to get the proper slope.  In addition we always recommend solid metal or plastic extensions, 10' if possible.  With a good slope and the longer length it will help get that water away from the problem areas.  This extension (the green piece) is also pointed towards the left when it should be pointed at us which would make it easier to hit the slope of the yard heading towards the right.  With this set up the water is getting dumped into the pea gravel (towards the left) but then heading to the right.  Along the route is this nice stair step crack that most likely goes from floor to ceiling in the basement

This basement has a working drain tile system but when there's rain, some of the water does work it's way into the system but the crack we see on the outside is also visible on the inside and taking the path of least resistance, it dumps out above the floor, skipping the drain tile system.

Great article from the Billings Gazette about the bentonite industry.  While this material has hundreds of uses, it's properties make it perfect for exterior foundation waterproofing.

 

 

 

May 21, 2012 12:00 am  •  By MARTIN KIDSTON mkidston@billingsgazette.com

GREYBULL, Wyo. — Applications to mine “the clay of 1,000 uses” are pouring into the Bureau of Land Management as companies look to capitalize on the bentonite boom and keep pace with the nation’s rebounding economy.
From mines at Frannie to Bearcreek, companies have ramped up production, racing to extract a commodity that was deposited millions of years ago as volcanic ash and chemically reworked in a shallow, inland seaway.
At M-I Swaco’s mine east of Greybull, BLM geologist Gretchen Hurley holds a lump of bentonite in her hand. With the consistency of Play-Doh, the damp product is easily shaped, rolled and squeezed.
“I think the new applications are a result of companies trying to get ahead of the permitting curve, because it takes a while to permit one of these mines,” Hurley said. “If we can get them approved for a 500-acre mine, that’ll keep them supplied in bentonite for 10 to 30 years.”
Bentonite has the ability to swell to 16 times its original size and absorb 10 times its weight in water. It’s used in cat litter and beauty supplies and as a binding agent in animal feed. It’s also used in foundry work and in drilling, including in the Bakken field of North Dakota.
The clay’s industrial uses tie it directly to the nation’s energy and auto industries. With the economy on the mend, the bentonite industry has followed suit, restoring jobs lost in 2008 while creating an increase in mining applications across the region.
At the American Colloid plant east of Lovell, plant manager Steve Wilkerson said that at height of the recession, around 42 employees lost their jobs. Around 30 of those jobs have been restored and production has increased, surpassing pre-recession figures.
“Before the recession we were running at around 650,000 to 700,000 tons a year,” Wilkerson said. “In 2008, we dropped off to around 280,000 tons. At the present moment, the way things are going right now, we should be back at around 750,000 to 780,000 tons.”
Bentonite means business
The life of a bentonite mine depends on market conditions, and it’s Lyndon Bucher’s job at American Colloid to ensure that a steady flow of clay is available to keep pace with customer demands, including the oil industry, General Motors and Caterpillar.
Bucher, who works in American Colloid’s permitting and reclamation department, said that like all mining operations, clay is subject to booms and busts. Business lately has been up.
“Bentonite is considered an industrial mineral, and so it goes into a number of different products,” Bucher said. “You could say we’re something of a bellwether for the national economy. For the most part, as the economy goes, so goes the bentonite industry.”
Wyoming’s annual bentonite production has risen from 1,400 tons in 1927 to more than 4.5 million tons. Five companies are engaged in 19 active mining plans across several counties in Montana and Wyoming, according to the BLM.
“I’m supposed to maintain at least five years of permitted reserves in every grade of bentonite,” Bucher said. “We’ll do the exploration drilling to locate and grade the product. Once the exploration is done, we know where we need to permit.”
This arid region of the basin, which extends down the western front of the Pryor and Bighorn mountains in Montana and Wyoming, is considered one of the world’s top producers of high-swelling, sodium-type bentonite clay, representing nearly 70 percent of the world's known supply.
According to the Wyoming Mining Association, the industry employs about 605 workers in the Bighorn Basin, including mill operators, mechanics, surveyors, packaging operators and laboratory technicians. For every job provided by the industry, an estimated three additional jobs are created in the community.
In Wyoming, where most of the activity takes place, the industry contributes more than $11.3 million in taxes and royalties. Its annual payroll with benefits comes to roughly $48.3 million, with nearly 70 percent of that paid to employees in the Bighorn Basin.
“Without the bentonite industry, you could fold Big Horn County up and it would go away,” said county Commissioner Keith Grant. “Of our top 10 assessed valuations, four are bentonite companies. The top two are oil and gas, and the railroad is in there, too.”
Remaining reserves
It wasn’t until 1888 that the first commercial shipment of bentonite was made. The clay earned its name from discoveries in Montana’s Fort Benton Formation. It’s been sought after ever since.
Large-scale bentonite mining and processing in this region began near Greybull in the early 1950s. More than 21,000 acres have been mined in the Bighorn Basin to date, according to the BLM.
On the hood of her truck, Hurley lays out a map with the mines designated in red. The bentonite sought by companies lies in a north-south trend along the eastern rim of the basin.
“This whole horizon of gray shale that’s in front of us — we’re looking at a long strike, or a trend, and there are bentonite beds all along that profile,” Hurley said. “It’s a big, huge area.”
Hurley said an inland sea once covered this region while mountain-building volcanoes to the west spewed ash. The ash settled into the sea, where it was chemically worked over time.
Buried by sand, pressurized and compressed, it became the product rolling by the ton into the basin’s plants. There, it’s dried, processed and packaged in powder and granular forms to meet customer needs.
“There are several different beds, and each bed has its own unique properties,” said Jason Schneider, the mining operations manager with American Colloid. “We’re trying to select different beds to meet the demands for the final product.”
Standing at a cross-cut at the Frannie mine on the state line, Schneider notes the striated layers of shale and the bed of bentonite below. Even here in this small pit, no more than an acre in size, the bentonite comes in yellow and blue.
Schneider said each bed of clay is given to a different set of qualities suited for a variety of industrial uses. It’s up to the companies to extract and process the right clay for the job.
“For this location, it’s a lot of drilling mud,” Schneider said. “With the activity in North Dakota, in the Bakken, that increases the demand for drilling mud. Foundry work has been real strong as well — the auto market. Those things are coming back, and when the economy starts to pick up, you see it on this end.”
Estimates vary on how much accessible bentonite remains here in the ground. A 1989 report by the American Institute of Mining Engineers suggests that around 1.1 billion tons have yet to be mined.
A 1980 edition of the U.S. Bureau of Mines, Minerals, Facts and Problems lists bentonite reserves of around 200 million tons. Either way, it’s enough to keep the bentonite industry supplied for years to come.
“If it’s oil and gas drilling, we’ll target a specific clay for that, and if it’s cat litter, we’ll target another clay for that,” Bucher said. “We have many different customers, and we’ll try to meet the market demand by mining in these different areas and getting the right quality of clay into the plant.”

For those looking for exterior bentonite pressure injection for waterproofing you've found the right place.  Exterior waterproofing using bentonite was discussed on the Home Improvement Show with Lindus Construction on WCCO Radio Saturday Morning with the experts agreeing that stopping water on the exterior (with bentonite) is the best way to truly waterproof your foundation.

The example presented was a wet basement floor leaking from the seam the floor and wall make.  In most cases this is a cold joint with no gasketing meaning that it's two pieces of concrete installed at different times.  Once the water pressure outside is high enough it will push water through this area.

Using a waterproofing mix of all-natural bentonite, Great Lakes Waterproofing fills the water-pathways, once the bentonite sets up water cannot pass through it, creating a waterproof barrier.  More water pressure just pushes the bentonite tighter against the foundation.

For new construction we can install a bentonite membrane before the concrete is poured.  We overlap all the seams and cover everything below grade.  Once backfilled this is one of the most durable types of waterproofing known.

My Concrete Wall Is Leaking!

This is one of my favorite wet basement photographs, and really backs up the phrase "a photo is worth a thousand words."   The photo shows an inside foundation wall with some insulation removed.  This wet basement area was leaking a great amount of water on the floor during big rains.  The home owner was mad because they had a drain tile system but it was dry most of the time.  The photo shows a vertical wall crack and the dark area is water on the foundation and floor and what's left of a tie rod above the black corrugated channel on the floor.  With poured walls, tie rods were used to hold forms together when they poured the walls.  When the concrete sets, the forms are pulled but the contractor has no choice but to leave these tie rods in the concrete (they normally bust off the protruding tab ends).  Made of metal, these tie rods rust when exposed to water, this one is no different leaving a good size hole in the wall and possibly providing a stress point that lead to the vertical crack. 

The black corrugated channel is supposed to capture this water and drain it down to an underfloor drain tile system leading to a sump pump and sump pit.  This drain tile system has failed here and a few other places in this basement and we see this type of drain tile failure often especially when the water comes out above the floor.

Great Lakes Waterproofing uses all methods of waterproofing, they all have their strong points, but we love to do exterior waterproofing and really seal up the foundation.  In most cases, exterior hydroclay waterproofing is the least costly.  In this situation we injected all-green bentonite hydroclay along this side of the home, filling in voids and cracks.  Once set up water is not able to get through this barrier and after a year and a half of record rain fall this basement is dry again.

For customers wanted to address the crack as well, we offer Fortress Stabilization Carbon Fiber Strips.  We would use marine grade epoxy and attach carbon fiber strips to staple up the crack preventing it from future movement.
www.TCWaterproof.com 

Waterproofing older homes and buildings

Great Lakes Waterproofing is proud to have been selected to waterproof the historic home of President Benjamin Harrison located in beautiful Indianapolis Indiana  Great Lakes Waterproofing does several similar projects using our exterior waterproofing system that consists of injecting bentonite clay, or hydroclay, around the perimeter of the home.  In most cases excavation is not necessary since we use small diameter pipe that's pushed down to the footing (basement floor level).  Keeping the landscaping intact and having little intrusion on the interior is why homowners and business owners chose Great Lakes Waterproofing. While interior drain tile systems have a place, most buildings and homes are better suited for exterior waterproofing, stopping water before it gets inside. 

In older homes there are several reasons an underfloor drain tile system is not considered, such as, disturbing the basement floor might not be an option, or the basement area is finished and putting in an underfloor drain system will cause too much damage.  One of the most common issues is if the walls are poured (solid concrete) or the builder used solid rock, limestone walls are very common in the Midwest.  Drain tile is very ineffective with these mostly solid walls, the water enters the basement above the floor and cannot get into the drain tile system.

 

That brings us back to exterior waterproofing, not only are we sealing off the water pathways but we also help the stone and mortar stay drier, ensuring longer life.

 

www.TCWaterproof.com

 

 

. 

Exterior Waterproofing on Historic Buildings

We're heading into the fall rainy season again and Great Lakes Waterproofing is leading the way with exterior waterproofing. While we work with most products and systems available, sealing the foundation from the exterior is our preferred method.  A lot of our Bentonite waterproofing projects involve older, maybe even historic, structures.  Bentonite (Hydroclay) Waterproofing works great because it fills in voids, follows the water and seals the passageways.  Once properly set up the foundation will have the time-tested proven properties of Bentonite.

Historic and older properties can be a little more difficult to address for exterior waterproofing, buildings were often built closer to sidewalks and parking lots.  If excavation were necessary the costs would go up tremendously.  Great Lakes Waterproofing addresses these issues by drilling small holes around the perimeter and pumping under the obstruction.  this building is typical of what you might find in the downtown district, construction is solid stone foundation and brick above grade with an asphalt patio area.  Water is coming in through this side so that's the area we'll do our exterior waterproofing.      

After drilling several small holes near the foundation, we pump our Bentonite sealing up this part of the wall.  In the photo is an injection wand, extending down around 8'-10', and hose that's connected to the pumping equipment.  Our industrial pumping equipment is capable of pumping long distances, this patio area was sealed off by a fence and we only had limited access, not only would excavating this area be difficult, most of it would have to be done by hand. 

The front side of this building also presented it's own challenges, even with the concrete all the way up to the foundation, this building had major water issues.  The solid stone walls were fine but over time some of the mortar joints opened up allowing free-flowing water to enter the building.  Since the water was entering above the floor and the wall was solid, the owner decided to go with exterior waterproofing.  Excavation and digging were cost prohibitive but Bentonite waterproofing seemed like the perfect product for this application.

After drilling small holes along the perimeter, Bentonite is pumped all the way down to the footings (basement floor level), this photo is neat because you can see the clay coming back up a hole that's over six feet away.  Once the Bentonite sets up, the water that used to flow in this "void" will not be able to pass through the Bentonite. 

Visit us at the Home Builders Association Home Show

Once again Great Lakes Waterproofing is at the Home Builders Association of Kalamazoo's Home Show. From March 11 through the 14th feel free to talk to our sales engineers about any issues with your basement, parking garage, elevator pit, etc.

This is a great opportunity to learn more about our services including hydroclay injection, sump pump installation and repair, wall reinforcements, elevator pit waterproofing.

More information can be found at the following site http://sites.google.com/site/kalamazoohomepage/

Drain Tile & Cove Drain in Action

Wow, a picture sure is worth a million words. In this wet basement photo we have a block wall filled with water. It has the typical signs including staining of the wall at the mortar joints, cracks with staining and moisture present. The homeowner has installed both a drain tile system and a cove drain system.

The drain tile system is high-end with a nice control panel for the pump and there's probably a battery back-up for the pump install in another room in case there's a power failure. The white PVC pipe is the sump pump discharge that goes out to the yard.


There's also a cove system installed at floor level. Several holes have been drilled into the cinder block cores at the floor level to relieve any water that fills the concrete blocks. Cracks in the outside wall have allowed water to build up in the blocks and the holes should provide an exit for the water which drains into the channel that leads to a sump pump.


Great Lakes Waterproofing was called in because this area was still getting wet and not a little wet but a lot wet, in fact a hole that someone had drilled into the block had a stream of water pouring out of it. Not only was the hole drilled 33" above the floor level but the blocks were full of water at this level. (a cinder block holds approximately 1.7 gallons of water)

The upper photo is roughly 7.5' wide by 4'+ tall, there's close to 51 gallons of water in this area of block, maybe more looking at the staining on the bottom course of white block. Imagine a typical city house with a footprint of 24' x 24', one wall could have hundreds of gallons of water in the blocks.


In this situation Great Lakes Waterproofing sealed the outside of the basement wall stopping the water before it filled the blocks truly waterproofing the basement

The cove system failed because rocks and debris clogged it up the water was unable to drain into the channel. The drain tile system failed for the same reason, the cracks on the outside wall were large enough to allow rocks and debris to fill up the first course of block, once filled both systems don't have a way drain the water. What options do you have when your water management system fail?

Landscaping and Waterproofing

While landscaping can help with waterproofing your wet basement several steps need to done to insure water is running away from the foundation and not into the basement. This house had the entire yard landscaped with rocks, plants, mulch and a multi-tiered rock wall.

Above the basement wall is a board called the sill plate. The sill plate is a horizontal wooden board attached to the concrete basement wall and supporting the above ground walls. This board should be at least 6"-8" above the finished grade.

This photo shows new landscaping that's been graded as high as the sill plate. Although you can't see it, the bottom of the sill plate is even with the bottom of the rock siding. The area in the center of the photo also has a small slope towards the home and rock wall.

During a rain storm, water would build up in the center area and enter the house between the sill plate and basement wall. While the house had a drain tile system none of this water was captured and ended up on the floor creating a very wet basement.

Some of the signs that the water is coming in from above ground include stains on the wall as in the case of this window. In this case heavy rains would spill over the window frame into the basement area. Once again a drain tile system would not work with this wet basement.

http://www.tcwaterproof.com/ http://www.greatlakeswaterproofing.com/

Waterproofing or Water Management?

When asked what they would prefer, waterproofing or water-management, most customers would like waterproofing. What's the difference? Waterproofing keeps moisture outside while water-management still lets the water inside, diverting it to a tank and pumping it back outside. There's only one way to have a truly dry basement....stop the water before it has a chance to get inside.

One of the most popular "waterproofing" systems is the installation of Drain Tile. Basically a trench is excavated around the walls of your basement and a perforated pipe is installed and new floor is poured over the pipe. The pipe drains to a tank in the floor which gets pumped outside when filled with water.

Another popular system, used with block walls, involves drilling holes near the floor into the blocks. The theory behind this is that the blocks fill with water and the holes will help with drainage. A plastic channel is fastened to the wall to capture the water and drain into a tank similar to the drain tile system.

Both of these systems have serious red flags including:

Power failure....What if the power goes out during a major storm and the sump pump stops? You guessed it, a basement full of water

Pump failure....It doesn't take much, an old pump (remember these are usually sitting in the bottom of a tank full of water), dirty water, rocks, string can all spell disaster.

Moist basement....These systems are still letting the water in providing a nice place for mold to grow and that damp, musty odor to flourish

Erosion of the foundation....While draining water these systems are also pumping out dirt and gravel that was once around the foundation. Over time you are slowly destroying the foundation of your home and providing an easier path for water to get in. Ever noticed how sidewalks next to older homes always seem to be sloping towards the house? The foundation has washed away allowing the sidewalk to sink and at the same time increasing the amount of water into the basement.

The leak must be at the floor level....In theory these systems seem great but what if the water is coming in half way up the wall? Neither will be able to capture this water and properly get rid of it.

Around 40% of our installations are homes or pits with existing drain tile or drain cove systems. Either the owner was fed up with the maintenance required or the system was not working properly or it was running all the time. By stopping the water before it can even get in, we truly waterproof and don't water manage.

There's Water In My Elevator Pit

Recently one of our sales engineers was faced with the task of helping waterproof an elevator pit. The basic construction of a pedestrian elevator includes a pit 10'-20' below the last floor for counterweights, wiring and a giant hydraulic safety stand. The building this three-stall elevator pit was located in was next to a large rocky limestone hill and about 200' from a river. Wall construction was poured concrete in good to excellent condition.
While the pit was set up with an exposed cove drain tile system around the wall leading to the sump pump the rest of the floor was not protected and over time water was noticed coming through some of the bolt holes drilled into the floor holding up the tracks for the elevator. In addition there were several areas around the seam at the wall and floor that water was creeping through including a larger leak the size of a pencil that water was coming out of in a steady stream.

Using our exclusive bentonite hydroclay injection system the installers at Great Lakes Waterproofing tackled the problem by drilling holes near the leaks and injecting our waterproofing blend of bentonite hydroclay. Right away the flow of water had stopped at the bolt holes. The next step was to waterproof the perimeter, not an easy task as it was flowing over a gallon of water into the sump every minute. Our waterproofing blend of bentonite hydroclay is an all natural product that stays flexible throughout it's lifespan, the self-sealing nature of the clay is perfect for this application that has many dynamic water forces at work.

Once again our waterproofers drilled holes every few feet straight down through the concrete into the sand and water. Working fast to make sure the sump pump was not overwhelmed by the water coming in through the new holes, the Great Lakes Waterproofing Team pumped bentonite waterproofing into all the holes and capped them off with hydraulic cement. for a permanent waterproofing solution.

Another elevator pit we waterproofed contained a large hydraulic lift for it's industrial elevator. Typically the shaft is buried as deep as it's height above the floor, in this case over three stories.
The old lift had started leaking hydraulic fluid and needed to be replaced. The floor around the old shaft was broken out, the new shaft installed and concrete was poured around the new shaft. Several areas of repaired concrete around the new shaft developed leaks. The elevator pit floor was next to a river and 5-10' below the surface of the water, developing a lot of hydrostatic pressure on the exterior of the elevator pit. The pit had 2-3" of water and the sump pump was running continously 24 hours a day.

Once again we drilled through the concrete floor and pumped in our waterproofing blend of bentonite hydroclay. Several areas around the pit needed attention. Once the hydroclay was installed and the pit started to dry we closed all the holes off with hydraulic cement. In addition to drying up the elevator pit, the industrial sump pump is now dormant.

Things are looking good now in these dry elevator pits, this is another example of bentonite waterproofing we can do at a fraction of the cost the other guys charge to divert the water.